| 77202B Franke Slewing Ring Bearings | B:38.887 mm; α:6 °; Mass plain bearing:0.64 kg; Basic dynamic load rating C:170 kN; Specific dynamic load factor K:100 N/mm²; Design (sliding contact surface combination):Steel/steel, heavy-d; Da max.:67.4 mm; Sealing solution:Triple-lip seals; Basic static load rating C0:510 kN; C:33.325 mm; r1 min.:0.6 mm; b:4.8 mm; Material constant KM:330; dk:63.881 mm; d:44.45 mm; da min.:48.5 mm; rb max.:1 mm; |
| 68965A Franke Slewing Ring Bearings | B:12.00 mm; Grease Speed Rating Open/Shielded n1:15000 rpm; Oil Speed Rating Open/Shielded n2:18000 rpm; Sealed Speed Rating n3:9500 rpm; Accessories:One Shield & Snap-Ri; D:47.0000 mm; Fillet Radius ra:0.64 mm; Basic Static Radial Load Rating Co:6550 N; Basic Dynamic Radial Load Rating C:11200 N; d:25.000 mm; |
| 68617A Franke Slewing Ring Bearings | Basic Dynamic Radial Load Rating C:92300 N; Fillet Radius ra:1.00 mm; Fillet Radius rb:0.60 mm; d:85.000 mm; B:44.00 mm; Basic Static Radial Load Rating Co:116000 N; Oil Speed Rating n2:14000 rpm; D:130.0000 mm; Grease Speed Rating n1:9600 rpm; |
| 68504A Franke Slewing Ring Bearings | r5 min.:0.3 mm; Ca min.:4 mm; Calculation factor Y0:1.6; Da max.:73.5 mm; Basic dynamic load rating C:129 kN; Calculation factor Y1:1.6; 2B:40 mm; Calculation factor Y2:2.3; K:4.5 mm; Mass bearing pair:0.78 kg; rc max.:0.3 mm; ra max.:1 mm; da max.:57 mm; b:5.5 mm; d:50 mm; Fatigue load limit Pu:19.3 kN; Da min.:72 mm; Reference speed:5300 r/min; Calculation factor e:0.43; Basic static load rating C0:176 kN; |
| 66199L Franke Slewing Ring Bearings | Max. speed for Taconite seal:1150 r/min; P120°:30.2 kN; P60°:83.2 kN; ba:30.163 mm; A1:88.9 mm; L:330.2 mm; Cap bolt:2 x 5/8-11 UNC; Stabilizing ring:2 x SR-1516; P180°:31.6 kN; Appropriate attachment bolt size G:0.75 in; P90°:49.8 kN; da:68.263 mm; Pa:6.23 kN; N1:22.225 mm; P150°:26.7 kN; Cap bolt recommended tightening torque:149.1 N·m; H1:88.9 mm; Ca:42.799 mm; Mass pillow block:16.4 kg; |
| 74108A Franke Slewing Ring Bearings | Oil Speed Rating n2:8000 rpm; B:27.00 mm; Basic Dynamic Radial Load Rating C:37700 N; Grease Speed Rating n1:6000 rpm; Accessories:Two Seals & Snap-Rin; D:72.0000 mm; Sealed Speed Rating n3:6000 rpm; Fillet Radius ra:1.00 mm; Basic Static Radial Load Rating Co:27500 N; d:35.000 mm; |
| 68645A Franke Slewing Ring Bearings | Calculation factor A:0.0344; Calculation factor Y0:0.26; ra max.:1.5 mm; r1,2 min.:1.5 mm; d2 ≈:69.32 mm; Calculation factor Y2:0.57; d1 ≈:79.6 mm; Calculation factor Y1:0.55; Da max.:101 mm; Mass bearing:0.8 kg; r3,4 min.:1 mm; Calculation factor e:1.14; D1 ≈:91.55 mm; Fatigue load limit Pu:2.12 kN; Basic dynamic load rating C:61 kN; Reference speed:7000 r/min; B:22 mm; rb max.:1 mm; |
| 68522A Franke Slewing Ring Bearings | r1,2 min.:1 mm; D1:122 mm; Mass housing washer:0.41 kg; B:7 mm; D:155 mm; |
| 77236B Franke Slewing Ring Bearings | Ca:55.804 mm; H:222.25 mm; P120°:52.5 kN; PG:1/4 NPT; Cap bolt, SAE grade:8; Taconite seal:TER 102; P150°:48 kN; P60°:141 kN; R1:58.737 mm; P180°:57.4 kN; da:87.313 mm; End plug (suffix Y):EPR 12; H2:44.45 mm; Pa:13.8 kN; J max.:333.375 mm; L:387.35 mm; Mass pillow block:40.4 kg; RG:3/8 NPT; N1:26.988 mm; A1:111.125 mm; |
| 77260A Franke Slewing Ring Bearings | N:21.5 mm; H2:19 mm; J max.:128 mm; A:40 mm; N1:14.5 mm; Fatigue load limit Pu:0.475 kN; Mass bearing unit:0.49 kg; Recommended diameter for attachment bolts, mm G:12 mm; L:159 mm; Housing material:Composite for food a; Basic static load rating C0:11.2 kN; Thread grub screw G2:1/4-28 UNF; Limiting speed:3800 r/min; Basic dynamic load rating C:16.3 kN; B:38.1 mm; d:31.75 mm; Recommended tightening torque for grub screw:4 N·m; |
| 73105L Franke Slewing Ring Bearings | d:190 mm; B1:125 mm; d1:180 mm; G:M 200x3; G1:20 mm; B2:131 mm; Hydraulic nut:HMV 40 E; Mass withdrawal sleeve:4.48 kg; |
| 68715A Franke Slewing Ring Bearings | Basic static load rating C0:200 kN; Basic dynamic load rating C:190 kN; Mass rod end:2.45 kg; Specific dynamic load factor K:150 N/mm²; d:45 mm; α:7 °; l1 min.:92 mm; l7 min.:50 mm; l2 max.:217 mm; B:32 mm; Material constant KM:330; C1 max.:28 mm; d2 max.:104 mm; h:163 mm; dk:60 mm; G:M 42x3; r1 min.:0.6 mm; |