| 68491A Franke Slewing Ring Bearings | H:222.25 mm; Housing:SSAFS 520; P60°:141 kN; R1:58.737 mm; Cap bolt recommended tightening torque:298.3 N·m; h:42.069 mm; Labyrinth ring:2 x LOR 100; Cap bolt, SAE grade:8; Mass pillow block:21.8 kg; L:387.35 mm; RG:3/8 NPT; Ca:55.804 mm; Cap bolt:5/8-11 UNC; Bearing limiting speed:4500 r/min; A1:111.125 mm; da:84.138 mm; PG:1/4 NPT; ba:44.45 mm; P90°:84.5 kN; Initial grease fill:181.44 g; |
| 68959A Franke Slewing Ring Bearings | ra max.:6 mm; T:93.662 mm; Da min.:900 mm; da max.:820 mm; Limiting speed:500 r/min; Reference speed:340 r/min; r1,2 min.:6.4 mm; Cb min.:26.5 mm; db min.:806 mm; D:965.2 mm; d1 ≈:853.1 mm; C:66.675 mm; Db min.:924 mm; Calculation factor Y0:0.8; Ca min.:10 mm; Calculation factor Y:1.5; rb max.:3.1 mm; r3,4 min.:3.3 mm; Mass bearing:131 kg; Dimension series:EE 752000; |
| 68737A Franke Slewing Ring Bearings | Basic dynamic load rating C:426 kN; J1:57.15 mm; B:80.169 mm; s:38.497 mm; da:100.013 mm; H1:107.95 mm; S:0.794 mm; J max.:333.375 mm; Mass bearing unit:22.5 kg; Attachment bolt diameter G:19.05 mm; H2:61.913 mm; L:387.35 mm; Limiting speed:2200 r/min; A:114.3 mm; J min.:304.8 mm; H:217.488 mm; |
| 77202B Franke Slewing Ring Bearings | B:38.887 mm; α:6 °; Mass plain bearing:0.64 kg; Basic dynamic load rating C:170 kN; Specific dynamic load factor K:100 N/mm²; Design (sliding contact surface combination):Steel/steel, heavy-d; Da max.:67.4 mm; Sealing solution:Triple-lip seals; Basic static load rating C0:510 kN; C:33.325 mm; r1 min.:0.6 mm; b:4.8 mm; Material constant KM:330; dk:63.881 mm; d:44.45 mm; da min.:48.5 mm; rb max.:1 mm; |
| 77250A Franke Slewing Ring Bearings | d2 max.:75 mm; l2 max.:149 mm; dk:40.7 mm; l1 min.:65 mm; C1 max.:20 mm; B:22 mm; h:110 mm; d:30 mm; Material constant KM:330; Basic dynamic load rating C:62 kN; r1 min.:0.6 mm; Specific dynamic load factor K:100 N/mm²; α:6 °; l7 min.:34 mm; Mass rod end:0.9 kg; Basic static load rating C0:81.5 kN; G:M 30x2; |
| 73118L Franke Slewing Ring Bearings | Housing:SAF 032 KA; P150°:68.1 kN; Cap bolt:2 x 1-8 UNC; Appropriate attachment bolt size G:0.875 in; PG:1/4 NPT; Taconite seal:TER 130; J max.:406.4 mm; A2:277.813 mm; Pa:25.4 kN; H2:60.325 mm; ba:59.531 mm; P90°:113 kN; R2:36.513 mm; H1:152.4 mm; Max. speed for Taconite seal:560 r/min; End plug (suffix Y):EPR 16; J1:82.55 mm; h:51.594 mm; P180°:84.5 kN; Cap bolt, SAE grade:8; |
| 68965A Franke Slewing Ring Bearings | B:12.00 mm; Grease Speed Rating Open/Shielded n1:15000 rpm; Oil Speed Rating Open/Shielded n2:18000 rpm; Sealed Speed Rating n3:9500 rpm; Accessories:One Shield & Snap-Ri; D:47.0000 mm; Fillet Radius ra:0.64 mm; Basic Static Radial Load Rating Co:6550 N; Basic Dynamic Radial Load Rating C:11200 N; d:25.000 mm; |
| 66154L Franke Slewing Ring Bearings | Cap bolt, size:M 42x280; Q180°:2900 kN; ATS:470 mm; H:835 mm; N:60 mm; H1:420 mm; ba max.:238 mm; Eye bolt, size:2 x M 42; ATK:590 mm; s:35 mm; da:500 mm; P0°:8000 kN; P120°:3600 kN; Initial grease fill, 20%:10.5 kg; P180°:4000 kN; J1:260 mm; P55°:10000 kN; A:460 mm; Initial grease fill, 40%:16 kg; Labyrinth seal:2 x TS 560; |
| 68499A Franke Slewing Ring Bearings | d:105.000 mm; Sealed Speed Rating n3:2400 rpm; Basic Dynamic Radial Load Rating C:79300 N; Grease Speed Rating Open/Shielded n1:4000 rpm; B:26.00 mm; Basic Static Radial Load Rating Co:65500 N; Oil Speed Rating Open/Shielded n2:4800 rpm; Accessories:Two Seals & Snap-Rin; D:160.0000 mm; Fillet Radius ra:2.00 mm; |
| 74074A Franke Slewing Ring Bearings | Sealed Speed Rating n3:2200 rpm; D:180.0000 mm; Accessories:One Shield; B:73.00 mm; Basic Static Radial Load Rating Co:176000 N; d:85.000 mm; Grease Speed Rating n1:2200 rpm; Basic Dynamic Radial Load Rating C:195000 N; Fillet Radius ra:2.50 mm; Oil Speed Rating n2:3200 rpm; |
| 68627A Franke Slewing Ring Bearings | H1:76.2 mm; J min.:206.375 mm; Cap bolt, SAE grade:5; S:3.969 mm; db:77.787 mm; PosiTrac Plus contact element (dc shaft position):B10724-37; H:147.637 mm; PG:1/8 NPT; P60°:50.3 kN; RG:1/8 NPT; A1:79.375 mm; Pa:12 kN; Housing:SAF 213; P90°:30.2 kN; L:279.4 mm; Cap bolt:2 x 1/2-13 UNC; Labyrinth ring (db shaft position):LOR 55; A2:112.713 mm; Ca:39.014 mm; da:65 mm; |
| 68713A Franke Slewing Ring Bearings | Pa:3.47 kN; P120°:17.3 kN; R2:15.875 mm; Ca:30.785 mm; J min.:187.325 mm; Housing:SAF 511; A2:171.45 mm; P180°:19.1 kN; Da:100 mm; P60°:44.9 kN; H1:69.85 mm; PG:1/8 NPT; ba:25.4 mm; RG:1/8 NPT; Taconite seal:TER 22; Cap bolt recommended tightening torque:81.3 N·m; End plug (suffix Y):EPR 5; P90°:27.1 kN; L:244.475 mm; N1:19.05 mm; |