| 68954A Franke Slewing Ring Bearings | D:110.0000 mm; Basic Dynamic Radial Load Rating C:63700 N; d:50.000 mm; B:40.00 mm; Basic Static Radial Load Rating Co:20000 N; Fillet Radius ra:2.00 mm; Grease Speed Rating n1:5300 rpm; Oil Speed Rating n2:6300 rpm; |
| 74116A Franke Slewing Ring Bearings | Basic Dynamic Radial Load Rating C:436000 N; Basic Static Radial Load Rating Co:655000 N; Grease Speed Rating n1:1200 rpm; Fillet Radius rb:1.00 mm; Oil Speed Rating n2:1600 rpm; d:170.000 mm; Fillet Radius ra:3.00 mm; B:104.00 mm; D:310.0000 mm; |
| 66143L Franke Slewing Ring Bearings | d:40.000 mm; B:58.00 mm; Fillet Radius ra:1.50 mm; Width C:23 mm; Basic Static Radial Load Rating Co:11200 N; Basic Dynamic Radial Load Rating:33800 N; Grease or Oil Speed Rating n1:4500 rpm; D:90.0000 mm; |
| 68470A Franke Slewing Ring Bearings | Width Plain B:7.1 mm; Shielded or Sealed B1:8.7 mm; Accessories:Without Accessories; Grease Speed Rating Open/Shielded n1:18000 rpm; Oil Speed Rating Open/Shielded n2:22000 rpm; Basic Dynamic Radial Load Rating C:6050 N; Basic Static Radial Load Rating Co:3250 N; d:15.900 mm; D:34.9000 mm; Sealed Speed Rating n3:13000 rpm; Fillet Radius ra:0.79 mm; |
| 77218B Franke Slewing Ring Bearings | Grease Speed Rating n1:1300 rpm; Fillet Radius rb:1.00 mm; Oil Speed Rating n2:2200 rpm; B:84.00 mm; d:170.000 mm; Fillet Radius ra:2.50 mm; Basic Dynamic Radial Load Rating C:312000 N; D:265.0000 mm; Basic Static Radial Load Rating Co:465000 N; |
| 68739A Franke Slewing Ring Bearings | Basic static load rating C0:19 kN; Fatigue load limit Pu:0.8 kN; J max.:146 mm; Thread grub screw G2:M6; B1:42.9 mm; H1:49.2 mm; J min.:125 mm; Hexagonal key size for grub screw N:3 mm; J6:161 mm; Recommended diameter for attachment bolts, inch G:0.5 in; A:48 mm; A5:23.5 mm; N1:14 mm; Mass bearing unit:1.8 kg; Limiting speed:950 r/min; Housing material:Cast iron; Housing:SY 508 M/VZ033; d:40 mm; Recommended tightening torque for grub screw:7.4 N·m; |
| 66397L Franke Slewing Ring Bearings | D:120 mm; Calculation factor e:0.35; Da min.:104 mm; Fatigue load limit Pu:39 kN; Ca min.:4 mm; b:8 mm; r3,4 min.:2 mm; d:55 mm; K:4.5 mm; da max.:72 mm; Basic static load rating C0:325 kN; Basic dynamic load rating C:302 kN; Calculation factor Y0:1.8; Limiting speed:5600 r/min; 2B:58 mm; T:63 mm; Reference speed:3800 r/min; Calculation factor Y2:2.9; rc max.:0.6 mm; Da max.:110.5 mm; |
| 66157L Franke Slewing Ring Bearings | Specific static load factor K0:80 N/mm²; Permissible sliding velocity v max.:1 m/s; B:15 mm; Coefficient of friction µ min.:0.06; Specific dynamic load factor K:40 N/mm²; D:23 mm; Tolerance shaft:h9; d:20 mm; Tolerance housing:H7; Permissible sliding velocity v min.:0 m/s; Coefficient of friction µ max.:0.15; Mass bushing:0.0023 kg; |
| 77218A Franke Slewing Ring Bearings | B:42.9 mm; Thread length G1:12 mm; A:48 mm; Limiting speed:3200 r/min; Recommended tightening torque for grub screw:6.5 N·m; Hexagonal key size for grub screw N:3.969 mm; Housing material:Composite for food a; A5:28.8 mm; s1:25.4 mm; H:95 mm; Basic static load rating C0:15.3 kN; d:31.75 mm; H1:47.6 mm; J:82.6 mm; Fatigue load limit Pu:0.655 kN; L:110 mm; Basic dynamic load rating C:21.6 kN; |
| 73118L Franke Slewing Ring Bearings | Housing:SAF 032 KA; P150°:68.1 kN; Cap bolt:2 x 1-8 UNC; Appropriate attachment bolt size G:0.875 in; PG:1/4 NPT; Taconite seal:TER 130; J max.:406.4 mm; A2:277.813 mm; Pa:25.4 kN; H2:60.325 mm; ba:59.531 mm; P90°:113 kN; R2:36.513 mm; H1:152.4 mm; Max. speed for Taconite seal:560 r/min; End plug (suffix Y):EPR 16; J1:82.55 mm; h:51.594 mm; P180°:84.5 kN; Cap bolt, SAE grade:8; |
| 77262A Franke Slewing Ring Bearings | d:80 mm; h2:141 mm; d6:6 mm; Material constant KM:330; B:55 mm; α:6 °; dk:105 mm; l7 min.:98 mm; C1 max.:48 mm; l8:5 mm; l6 max.:237 mm; Basic dynamic load rating C:400 kN; r1 min.:1 mm; Basic static load rating C0:550 kN; Mass rod end:10.8 kg; Specific dynamic load factor K:100 N/mm²; d5 max.:97 mm; d2 max.:182 mm; |
| 68959A Franke Slewing Ring Bearings | ra max.:6 mm; T:93.662 mm; Da min.:900 mm; da max.:820 mm; Limiting speed:500 r/min; Reference speed:340 r/min; r1,2 min.:6.4 mm; Cb min.:26.5 mm; db min.:806 mm; D:965.2 mm; d1 ≈:853.1 mm; C:66.675 mm; Db min.:924 mm; Calculation factor Y0:0.8; Ca min.:10 mm; Calculation factor Y:1.5; rb max.:3.1 mm; r3,4 min.:3.3 mm; Mass bearing:131 kg; Dimension series:EE 752000; |