| 74070A Franke Slewing Ring Bearings | Basic static load rating C0:228 kN; Da max.:39.2 mm; Mass plain bearing:0.15 kg; Specific static load factor K0:500 N/mm²; C:16 mm; Design (sliding contact surface combination):Steel/PTFE fabric; d:20 mm; D:42 mm; Sealing solution:Triple-lip seals; ra max.:0.3 mm; rb max.:0.6 mm; Specific dynamic load factor K:300 N/mm²; Basic dynamic load rating C:137 kN; B:25 mm; α:17 °; r1 min.:0.3 mm; |
| 73081L Franke Slewing Ring Bearings | Calculation factor kr:0.083; Basic static load rating C0:1060 kN; Calculation factor X:0.35; a:263 mm; Calculation factor A:18.4; Db max.:611 mm; Reference speed:1000 r/min; D1 ≈:546.7 mm; Calculation factor e:1.14; rb max.:2 mm; Calculation factor Y2:0.57; ra max.:4 mm; Limiting speed:1000 r/min; Da max.:602 mm; d:420 mm; Calculation factor Y1:0.55; r3,4 min.:2 mm; B:90 mm; d1 ≈:498.4 mm; |
| 66145L Franke Slewing Ring Bearings | P150°:44.5 kN; R1:53.181 mm; Labyrinth ring (dc shaft position):LOR 54; J min.:244.475 mm; N1:19.05 mm; H2:31.75 mm; Cap bolt:2 x 5/8-11 UNC; P90°:82.7 kN; Max. speed for PosiTrac Plus seal:1450 r/min; S:4.763 mm; Cap bolt recommended tightening torque:298.3 N·m; Housing:FSAFS 216; Pa:33.8 kN; dc:76.2 mm; P120°:49.8 kN; Appropriate attachment bolt size G:0.625 in; L:330.2 mm; Cap bolt, SAE grade:8; |
| 66198L Franke Slewing Ring Bearings | d:710 mm; d3:900 mm; A:8 mm; G3:13 mm; Mass adapter sleeve assembly:379 kg; d1:670 mm; B1:467 mm; B:106 mm; G:Tr 710x7; B5:135 mm; Hydraulic nut:HMV 142E; G2:G 1/8; |
| 74102A Franke Slewing Ring Bearings | Basic Dynamic Radial Load Rating C:16100 N; B:15.00 mm; Basic Static Radial Load Rating Co:11200 N; Oil Speed Rating Open/Shielded n2:13000 rpm; D:52.0000 mm; Grease Speed Rating Open/Shielded n1:11000 rpm; Accessories:Two Shields; Fillet Radius ra:1.00 mm; d:25.000 mm; |
| 77236B Franke Slewing Ring Bearings | Ca:55.804 mm; H:222.25 mm; P120°:52.5 kN; PG:1/4 NPT; Cap bolt, SAE grade:8; Taconite seal:TER 102; P150°:48 kN; P60°:141 kN; R1:58.737 mm; P180°:57.4 kN; da:87.313 mm; End plug (suffix Y):EPR 12; H2:44.45 mm; Pa:13.8 kN; J max.:333.375 mm; L:387.35 mm; Mass pillow block:40.4 kg; RG:3/8 NPT; N1:26.988 mm; A1:111.125 mm; |
| 66200L Franke Slewing Ring Bearings | B4:6.75 mm; s1:32.3 mm; Db2:96 mm; Hexagonal key size for grub screw N:4.763 mm; Mass bearing unit:1.25 kg; Db1:88 mm; H:156 mm; L:96 mm; Fatigue load limit Pu:0.655 kN; Recommended diameter for attachment bolts, inch G:0.5 in; Recommended diameter for attachment bolts, mm G:12 mm; J7:15 mm; Basic dynamic load rating C:25.5 kN; T:53.3 mm; Housing material:Cast iron; d:34.925 mm; A:34.5 mm; J:130 mm; |
| 77238A Franke Slewing Ring Bearings | Cap bolt, SAE grade:5; A1:60.325 mm; Ca:28.804 mm; H2:20.637 mm; End plug (suffix Y):EPR 3; h:25.4 mm; da:38.1 mm; Max. speed for Taconite seal:2175 r/min; Initial grease fill:51.03 g; L:209.55 mm; RG:1/8 NPT; J max.:177.8 mm; J min.:158.75 mm; H1:57.15 mm; H:112.713 mm; R1:28.575 mm; Mass pillow block:5.17 kg; R2:12.7 mm; Appropriate attachment bolt size G:0.5 in; S:4.763 mm; |
| 68522A Franke Slewing Ring Bearings | r1,2 min.:1 mm; D1:122 mm; Mass housing washer:0.41 kg; B:7 mm; D:155 mm; |
| 74108A Franke Slewing Ring Bearings | Oil Speed Rating n2:8000 rpm; B:27.00 mm; Basic Dynamic Radial Load Rating C:37700 N; Grease Speed Rating n1:6000 rpm; Accessories:Two Seals & Snap-Rin; D:72.0000 mm; Sealed Speed Rating n3:6000 rpm; Fillet Radius ra:1.00 mm; Basic Static Radial Load Rating Co:27500 N; d:35.000 mm; |
| 73093L Franke Slewing Ring Bearings | H:156 mm; Hexagonal key size for grub screw N:3.969 mm; T:46.4 mm; Fatigue load limit Pu:0.655 kN; Recommended diameter for attachment bolts, inch G:0.5 in; A5:24.5 mm; B4:6 mm; B:42.9 mm; DN:6.5 mm; J:130 mm; N:14 mm; J7:15 mm; Basic dynamic load rating C:25.5 kN; SWN:7 mm; Housing material:Cast iron; Db2:96 mm; Limiting speed:5300 r/min; J6:106 mm; R1:22 mm; L:96 mm; |
| 74086A Franke Slewing Ring Bearings | P120°:55.6 kN; h:45.244 mm; Pa:39.6 kN; ba:50.006 mm; Taconite seal (db shaft position):TER 121; H1:125.425 mm; Housing:SAF 222; J min.:320.675 mm; db:123.825 mm; RG:3/8 NPT; J1:69.85 mm; Da:200 mm; Max. speed for Taconite seal:625 r/min; Cap bolt recommended tightening torque:203.4 N·m; da:110 mm; Initial grease fill:481.95 g; A1:120.65 mm; Taconite seal (dc shaft position):TER 113; R1:67.866 mm; |